HOW TO USE LADY-COMP & BABY-COMP

Lady-Comp and Baby-Comp are principally the same. Baby-Comp however comes with additional planning features, which will be explained separately from the common features. We have provided you with a general table of contents that will help you to understand all the different functions of Lady-comp / Baby-comp and how to use it.

You can select a specific topic from the menu and go directly to it or you can go through the information systematically by scrolling down the page.

CONNECTING LADY-COMP/BABY-COMP:

Please observe the following sequence:

1. First insert the electrical connection or battery box connection into the socket A (on the back of the device). Then connect to the mains supply. Press the plus and minus buttons once simultaneously. The correct time appears with a colon in the middle.
2. Lady-Comp/Baby-Comp automatically reverts to this display if no further command is entered for 90 seconds or when the plus and minus buttons are pressed simultaneously.
3. The thermometer is inserted in the socket B.
4. If you are using Lady-Comp/Baby-Comp with the battery box, press any button after connecting and the time appears.

Please also observe this sequence for setting the device in operation after an interruption, after a power cut etc.

BASIC RULES FOR ALL INPUT

The same principle applies to the input of any data into Lady-Comp/Baby-Comp.

Round Button

With the round button, you can change the levels (1). With the round button, you can make the device ready for setting by pressing and holding for 5 seconds (for example to change the time, the alarm time, the date). When the display flashes, it is ready for setting. Pressing and holding the round button for 5 seconds completes setting. The flashing stops and there is an acoustic signal to confirm the receipt of the desired input.

Plus Button

With the plus button, you can advance and enter data (for example to confirm menstruation). One press on the plus button advances the display by one unit. Hold the plus button down for fast forward.

Minus Button

With the minus button, you can go backwards in the display (for example to look at past temperature readings and evaluations). One press on the minus button reverses the display by one unit. Hold the minus button down for fast reverse. Data can also be corrected with the minus button.

Level 1: time, alarm time, date, year and test

Level 2: temperature reading, current day in cycle, fertility indicator
(current day, previous days and following days)

Level 3: only Baby-Comp: planning, fertilization day, birth date and sex prognosis

NECESSARY SETTINGS BEFORE COMENCEMENT:

When you take Lady-Comp or Baby-Comp out of its original packaging, the year, date and time are already correctly set.

1. Setting the alarm
Proceeding from the time display:

Press the minus button once.
The alarm setting 07.00 appears on the display.
Now hold down the round button for 5 seconds. The alarm time flashes.
Advance the alarm time using the plus button or
Reverse the alarm time using the minus button.
Input completed: press and hold the round button for 5 seconds.
The flashing stops and you hear an acoustic signal. The correct alarm setting appears on the display.

The device is ready to take a temperature reading:
+/-3 hours before or after the alarm time, if the alarm is switched on, or
+/-3 hours before or after the previous temperature reading time

2. Switching the alarm on and off (activating)
Proceeding from the time display:

Press the minus button once. The alarm setting appears.
Press the minus button again, the bell symbol flashes.
Press the plus button = the bell remains constantly illuminated. You will be woken up at the desired time.
Press the minus button = the bell disappears. You will not be woken up.

3. Taking your temperature the next morning
Place the thermometer under the tongue, right at the back, either to the left or the right of the frenulum with the mouth closed.
Press any button if the thermometer symbol is illuminated.
If the small thermometer symbol flashes, the device is ready for a temperature reading.
An acoustic signal indicates the end of the reading.
Your temperature reading appears in the display.

After the first temperature reading, the pictogram data = sample values (e.g. temperature reading 36.65) automatically disappear.

SEE DISPLAY SECTION

4. Fertility indicators: red = fertile green = infertile yellow = learning area

5. Menstruation data
After the temperature reading, the "M" symbol flashes.
If you are menstruating, press the plus button (M remains illuminated).
If you are not menstruating, press the minus button (M disappears from the display).
Give "M" input on at least three consecutive days.
If you have "M" and the machine does not ask you for input, activate "M"

OPERATING LADY-COMP AND BABY-COMP:

1. Setting the time

• Proceeding from the time display:
• Press the round button and hold for 5 seconds. The correct time flashes.
• Advance the time setting with the plus button.
• Reverse the time setting with the minus button.
• Input completed: press the round button and hold for 5 seconds. The flashing stops. You hear an acoustic signal to confirm your input.

Attention: If the time is set past 24.00 (either ahead or back), the date is automatically adjusted (ahead or back).

2. Setting the date

• Proceeding from the time display:
• Press the plus button once. The date appears.
• Now hold down the round button for 5 seconds.
• The date flashes.
• Press the plus button to advance the date setting.
• Press the minus button to reverse the date setting.
• Input completed: press and hold the round button for 5 seconds. You hear an acoustic signal. The date appears on the display.
• If the device has already received one or more temperature readings, it is only possible to reverse the date setting by one day. The temperature readings for the current day and the day before are deleted when the date is reversed. You can always advance the date by one day.
• It is impossible to change the date by accident.
• The year is automatically adjusted when you pass 31.12. Once the date has been correctly entered, it automatically proceeds correctly, with adjustments for leap years and the year 2000. This is irrespective of whether the Lady-Comp/Baby-Comp is operated with or without mains connection or battery.
• This is how you can correct the date when travelling in a different time zone. Do not take your temperature on the day of travel.

3. Setting the year

• Proceeding from the time display:
• Press the plus button twice. The year appears in the display window.
• Now hold down the round button for 5 seconds. The year flashes.
• Press the plus button to advance the year setting.
• Press the minus button to reverse the year setting.
• Input completed: press and hold the round button for 5 seconds. You hear an acoustic signal. The year setting appears on the display.
• The year setting can only be changed at the beginning. Once temperature readings have been entered, this is no longer possible.

4. Setting or changing the alarm

• Proceeding from the time display.
• Press the minus button once.
• The alarm setting (07.00) appears on the display.
• Now hold down the round button for 5 seconds. The alarm setting flashes.
• Press the plus button to advance the alarm setting.
• Press the minus button to reverse the alarm setting.
• Input completed: press and hold the round button for 5 seconds. The flashing stops. You hear an acoustic signal. The correct alarm setting appears on the display.

4.1. Switching the alarm on and off

• Proceeding from the time display.
• Press the minus button once.
• The alarm setting appears.
• Press the minus button once more and the bell symbol flashes.
• Press the plus button if you want to be woken up. The bell remains constantly illuminated. You hear an acoustic signal as a confirmation.
• If you do not want to be woken up, you should press the minus button when the bell flashes. The bell symbol disappears from the display.
• The bell lights up at the same time as the time display to confirm that you will be woken up the next day.
• If the bell does not light up with the time display, you know that you will not be woken up. This also applies to the following days.
• The Lady-Comp/Baby-Comp alarm starts off quietly and gradually becomes louder and louder.
• The alarm stops when you press any button and take a temperature reading or, otherwise, automatically after 1 minute.

4.2. Changing the alarm and temperature reading time

In principle, the device is ready for a temperature reading +/-3 hours before and after the time of the previous temperature reading. If you choose an alarm time outside these 6 hours, the temperature measuring time is adjusted to +/-3 hours in relationship to the new alarm time. This involves activating the alarm.

5. Taking your temperature, general information

• Taking the basal body temperature reliably, every day, is one of the key elements of our system. The more regularly that you take your temperature, particularly at the beginning, the faster the device gets to know your personal cycle.
• The basal body temperature is the temperature of the body just after waking up and before getting out of bed or becoming active in any way.
• Place the thermometer under the tongue, right at the back, either to the left or the right of the frenulum with the mouth closed.

5.1 Temperature reading time limit

• You can only take a temperature reading once a day and within the temperature reading time limit.
• The alarm must be activated before the first temperature reading.
• Lady-Comp/Baby-Comp controls the temperature reading time limit. It comprises 6 hours, beginning and ending three hours before and after the alarm time, or +/-3 hours in relationship to the previous temperature reading time if this differs from the alarm time.
• If there is no temperature reading for one day, the time limit is left open.
• The thermometer symbol remains illuminated throughout the temperature reading time limit
• Normally the alarm time and the temperature reading time are both the same. We recommend that you allow Lady-Comp/Baby-Comp to wake you up.
• If you wake up within the temperature reading time limit, e.g. to look after your child, take your temperature.
• If you get up late and the time limit is over, there is no reading for that day.

5.2. Taking your temperature Proceeding from the time display

• The thermometer symbol is illuminated. It is ready for a temperature reading.
• Now place the thermometer under your tongue, right at the back, either to the left or to the right of the frenulum.
• To take your temperature, press any button. The thermometer symbol flashes.
• The display shows temperature readings of 35.20 to 37.59 degrees. When, after approx. 30 seconds, the reading is completed, you hear an acoustic signal and the temperature reading appears on the display.
• If the temperature reading is interrupted, e.g. because the mouth is opened, the reading time is automatically extended. The temperature reading flashes to indicate an interruption.
• If the reading indicates that the temperature is too high (over 37.59), an "F" for fever appears on the display.
• If you do not want to take your temperature or want to interrupt the reading, you can stop the reading by pressing the minus and plus buttons simultaneously. You hear an acoustic signal. The device stops the reading. There is no temperature reading for this day.
• The tip of the thermometer can be cleaned using warm water. Occasional cleaning is recommended.

6. Menstruation data

Basically, you enter "M" on the days that you have "M". However, this should be on at least three consecutive days.

6.1. At the beginning

• In the event that the "M" = menstruation symbol flashes after the temperature reading:
• If you are menstruating, press the plus button, "M" remains constantly illuminated.
• If you are not menstruating, press the minus button. "M" disappears from the display.
• An acoustic signal confirms the data. The day of the cycle alternates in the display.

6.2. After using the device for some time

• When Lady-Comp/Baby-Comp knows your cycle, the device only asks about "M" when menstruation is expected. It begins to ask ("M" flashes) 2 days before.
• When "M" is finished, Lady-Comp/Baby-Comp stops asking "M" each day.
• The first bleeding after stopping the pill is not menstruation but is caused by the withdrawal of the medication. Do not enter "M" for this bleeding.

6.3. Activating "M"

• If you have "M" on a day that Lady-Comp/Baby-Comp does not ask for "M" please activate "M" yourself.
• Proceeding from the time display:
• Press the round button. You see today's temperature reading with the fertility report.
• Now press and hold the round button for 5 seconds.
• Enter "M" by pressing the plus button.
• The following days Lady-Comp/Baby-Comp will ask "M" automatically.

6.4. Correcting "M"

• Incorrect "M" data can be corrected.
• Proceeding from the time display:
• Press the round button once.
• If you want to correct the "M" data for the previous day, press the minus button. The date of the previous day appears on the display enabling you to enter or cancel "M".
• Press and hold the round button for 5 seconds.
• "M" flashes.
• Say no with the minus button. Say yes with the plus button.

6.5 Entering "M" at a later time

• If you have not taken a temperature reading for some time (e.g. on holiday), but menstruated during this time, you can enter this at a later time.
• You can go back to the desired date using the minus button. Then activate "M", as indicated in point 6.3.
• It is only necessary to enter the first "M" day. The device automatically records the following two days.

7. Fertility display

• Lady-Comp/Baby-Comp supplies information concerning fertility on every day of the cycle by using coloured display lamps.
• "red" = fertile
• "yellow" = learning area, ovulation late
• Yellow is only seldom displayed. If the device does not receive any 0 more data for a long period of time or receives information that it cannot evaluate, the number of "yellow" days increases again.
• "green" = infertile
• The number of green days increases cautiously and systematically.

Right from the beginning, the reliability of the displays corresponds to a Pearl-index of 0.7. This score corresponds to the test results collected from 686 women from three countries over a period of two years.

The reliability of a method of contraception is expressed for medical purposes by the Pearl-Index. The Pearl-index indicates how many unwanted pregnancies occur in 100 user years when using a specific means of contraception A contraceptive pill with a Pearl-index of 1 means that if 100 women use this pill for contraception for one year, one woman will get pregnant in this time. In general, Pearl-Index rates are as follows: pill 0.5-1, IUD 1-3, condom 5-15

8. "red" flashes (2 days)

Fertilization optimum. This means that the device expects ovulation in 1 to 2 days and sexual intercourse on this day is mostly likely to be successful". The display, flashing "red", is a prognosis. It becomes more and more accurate from cycle to cycle.

9. Potential fertility display

• Proceeding from the time display:
• Press the round button once.
• Press the plus button once to gain access to the potential fertility display.
• Press the plus button several times to see the expected fertility of the following 6 days.
• Every prediction is a statement of probability.

is an expectation and a prognosis. The actual level of fertility for the day for which the prognosis is made is shown on the day itself. This means that the prognosis for four days from now may be "green", but if ovulation is late and you are still fertile, the display will show "red" on day 4.

10. Monophases

• If there is no ovulation in a cycle, Lady-Comp/Baby-Comp indicates this to you. When this is the case the device stays on "red" or, if ovulation is late, it changes to "yellow" until "M" begins.
• A proportion of up to 20% monophase cycles can occur. If the proportion of monophases is higher, we can provide you with a printout of your cycle to discuss with your gynecologist. LC/BC printouts can help to diagnose insufficient production of gestagen (CLI).
• When you stop taking the pill, it takes some time before ovulation occurs again and you return to your own cycle.
• If you would like to have more information concerning this subject, please contact us. We have a data bank which is kept right up-to-the-minute.

11. Data from previous cycles (menstruation data)

• If you have information about your cycle, you can enter this data into the device before the first temperature reading. Activate "M" as explained on under point 6.5.
• It is possible to enter up to nine previous, consecutive "M" data. For each cycle, it is only necessary to enter the first "M" day, the device automatically saves three days.

12. Back in operation after an interruption

• The date, the year and the time continue to function automatically without connection to electricity or battery. If no temperatures are taken, the temperature reading time limit is left open and must be reset.
• This involves setting the alarm for the next morning and continuing in the usual way.
• If you want to enter "M" data, this is possible at any time. To enter "M" data at a later time, proceed as follows:
• Proceeding from the time display:
• Press the round button once.
• Then press the minus button once. The date appears. Now press the minus button as often as is necessary or press and hold until you reach the date for which you want to enter your first "M" day (beginning of cycle).
• Now press and hold the round button for 5 seconds. The date remains constantly illuminated and "M" flashes.

13. Sample values, test, trial readings

• Lady-Comp/Baby-Comp shows all displays as part of a test.
• Proceeding from the time display:
• Press the plus button 3 times.
• Lady-Comp/Baby-Comp now runs through all its symbols independently. The device tests itself and indicates this in the display window. When the test is completed the time appears and the thermometer symbol is illuminated.
• If you now press the round button, the thermometer flashes and is ready for a reading.
• You can now take your temperature or not, or interrupt a reading that has been commenced by pressing the minus and plus buttons simultaneously.
• Trial reading: proceeding from the time display 3x +
• You see the test is running. When it is completed the thermometer is illuminated. Now press any button and LC/BC is ready for a reading. If you take a temperature reading, the temperature is shown but not saved. If you do not take a reading, interrupt the process by pressing + and - simultaneously. Without taking a reading, the LC/BC interrupts the temperature reading process automatically.

14. Deleting memorized data

• Proceeding from the time display.
• With the left thumb, press and hold the round button.
• In addition, press and hold the minus and plus buttons, e.g. with the right thumb and the middle finger.
• Hold all three buttons for 5 seconds.
• If the display becomes lighter or darker while you are trying to cancel data, this means that you did not press the plus and minus buttons simultaneously.
• If the display is turned off, this again means that you did not press the plus and minus buttons simultaneously. Please start again from the beginning.
• An "L" appears on the display panel, with a "9" on the right. Let go of the three buttons.
• You must count down this "9" to zero by pressing the minus button 9 times. The cancellation process is interrupted if you touch any other button.
• Cancellation takes place automatically at zero. There is an acoustic signal. Then the current time appears on the display.
• In this way, it is impossible to delete memorized data by mistake.
• After deleting the data, you see the same information in the individual indicators as in the pictogram (e.g. temperature 36.65). After the first temperature reading, the pictogram data is automatically cancelled in the same way as when the device first became operational.
• Enter "M" by pressing the plus button. "M" remains constantly illuminated. Inaccurate "M" data can be cancelled by pressing the minus button.
• It is only necessary to enter the first "M" day. LC/BC automatically enters two more days.

15. Analysis of the cycle

• Proceeding from the time display:
• Press the round button once and the temperature reading of the day appears. This display alternates with the current day of the cycle.
• Now press the minus button once. The date of the previous day appears. This display alternates with the temperature reading of the day in question.
• The minus button enables you to go back.
• The plus button enables you to go forward.
• If you do not press any button for 1 minute and 30 seconds or when you press the plus and the minus button simultaneously, the recall process stops.
• You can recall all the previous temperature readings for up to 253 days by pressing the minus button again and again.

16. Print-out and evaluation

• If you are interested in receiving a detailed analysis of your cycle and a print-out of the data memorized in the device, send your Lady-Comp/Baby-Comp to our address.
• In the event of difficulties with your cycle or conception, a printout and evaluation can generally provide valuable information for you and your gynecologist, e.g. concerning the follicle phase, ovulation, the luteal phase and pregnancy.

17. Pregnancy display

• Lady-Comp indicates a probable pregnancy from the 15th day after conception by the simultaneous flashing of the red, yellow and green indicators
• The pregnancy is confirmed from the 18th day following fertilization by the simultaneous constant illumination of the red, yellow and green indicators 7

18. Battery operation

• You can also operate your Lady-Comp/Baby-Comp by using batteries/rechargeable batteries. You place 8 AA batteries or 8 rechargeable batteries (with more than 750 mAh) in your battery pack.
• All the same operations are possible with batteries as with mains power connection.
• If no button is pressed, Lady-Comp/Baby-Comp automatically turns itself off after half a minute. The display remains dark all day long and only lights up automatically the next morning when Lady-Comp/Baby-Comp wakes you up.
• If you would like to have some information during the day, you just need to touch a button and the displays light up.
• If, when using batteries, the display "BA-" appears, this means that it is time to change the batteries. The connection on the end of the cable belongs in the battery pack.

19. Mains supply

Lady-Comp/Baby-Comp is delivered with a120V mains power unit from us, or (alternatively) you can Euro, 230V mains power unit from us.

20. No risk of loss of data

In the event of a power cut, flat batteries or when changing batteries, there is absolutely no risk of losing the data memorised in the Lady-Comp/Baby-Comp or the data concerning menstrual cycles.

21. Regulating the brightness

• Any regulation of the brightness applies to the time display window and is maintained by the device until further changes are made. The other display windows always have the same normal degree of brightness.
• When you begin to use the device, the display shows the normal degree of brightness and is then reduced to the desired level.
• To dim: Proceeding from the time display:
• Press and hold the round button.Press the plus button simultaneously for lighter...or the minus button for darker
• The display gets darker if you are doing something wrong.
• The device can also be completely turned off using the dimming level if the Minus button is pressed repeatedly until you hear an acoustic signal. The device now functions as for battery operation.

22. Testing the sensor device

See point 13, Trial readings.

23. Summer and winter time

Set the time forward or back to summer or winter time. The date changes automatically when the clock passes 24.00

24. Pregnancy planning

• Baby-Comp shows you the optimum time for you to get pregnant.
• You can already see the optimum days to get pregnant flashing in display window 9 on the first days of a new cycle. Just two days per cycle are considered to be optimum. These days have no significance for the sex of the offspring and so the "boy and girl" symbols flash together with the date.
• In order to plan for a boy, only have intercourse on the day on which just the "boy" symbol is shown.
• If your preference is for a girl, only have intercourse on the day on which just the "girl" symbol is shown.
• Attention: the "boy" symbol lights up one day before the first optimum conception day. The "girl" symbol lights up one day after the second optimum conception day.
• Proceeding from the time display:
• Press the round button twice. The current date appears on the display.
• Now press the minus button and you will see the optimum conception date in window 9, red "boy"-, "girl"- and the sperm symbol.
• Then press the plus button twice and you will see the predicted date of birth in window 10, red "boy", "girl"- and the birth symbol.
• Attention: Before ovulation, the displays and symbols flash. After ovulation, they are constantly illuminated. If no prediction is possible, appears on the display.

25. Sex prognosis

During a possible or confirmed pregnancy, Baby-Comp indicates whether you can rather expect to have a boy or a girl. This is on condition that you entered SI input on the morning after intercourse. Both the boy and girl symbol will appear if intercourse took place on days on which it is equally likely for a boy or a girl to be conceived. This also applies if no SI was entered.

• Proceeding from the time display:
• Press the round button twice. The current date appears on the display.
• Now press the minus button and you will see the conception date (window 9) with the symbols "boy" and/or "girl" and the sperm symbol.
• Then press the plus button twice and you will see the estimated date of birth (window 10) with the symbols "boy" and/or "girl" and the birth symbol.

26. "SI" input

If YOU are planning a pregnancy and are interested in having a sex prognosis, inform Baby-Comp when sexual intercourse (SI) took place.

• Enter "Sl" data the following morning after taking a temperature reading.
• Proceeding from the time display:
• Press the round button twice to get into the planning level.
• Now press and hold the round button for 5 seconds.
• The "SI" symbol flashes.
• Say yes for "Sl" by pressing the plus button. An acoustic signal confirms the data.
• The "Sl" symbol remains constantly illuminated.
• If the device has received "Sl" information, it indicates on the fertile days whether there is more likelihood of conceiving a girl or a boy in the event of fertilization (see Pregnancy planning item 24).

27. Correcting "Sl" input

If you want to cancel incorrect "SI" input, you must do this on the same day (see point 26, but press the minus button to say no "SI" input).

28. Pregnancy display

Baby-Comp distinguishes between three pregnancy stages.

1. Possible pregnancy after 4-5 days red, yellow and green alternate (if Sl data has been entered)
2. Probable pregnancy after 15 days
3. Confirmed pregnancy after 18 days red, yellow and green flash red, yellow and green constantly illuminated

The displays for level 2 and 3 do not require "Sl" input

Baby-Comp indicates a possible pregnancy after the 4th-5th day after fertilisation. This very early indication can be made when SI (sexual intercourse) data has been entered on the following morning after the temperature reading and a possible pregnancy could be calculated. The fertility symbols red, yellow and green alternate.

After the fifteenth day Baby-Comp automatically indicates a "probable pregnancy". The fertility symbols red, yellow and green flash. If the likelihood of pregnancy is confirmed, there is a further display from the 18th day after fertilisation.

• All three colours are constantly illuminated. The conception and birth date can be called up onto the display in window 9 and 10 via the planning level (see point 29).
• Sex prognosis, on condition that "SI" data has been entered (also see point 25).
• Proceeding from the time display:
• Press the round button twice. The current date appears on the display.
• Now press the minus button, the conception date appears (window 9) with the symbols "boy" and/or "girl" and the sperm symbol.
• Then press the plus button twice and you will see the estimated date of birth (window 10) with the symbols "boy" and/or "girl" and the birth symbol.
• If a pregnancy is confirmed all displays are constantly illuminated.

29. Conception date and birth date

After ovulation has been recognised, Baby-Comp indicates the possible conception and birth dates in the planning level. These displays can be called up whether a pregnancy has taken place or not. The displays in window 9 and 10 are constantly illuminated.

• Proceeding from the time display:
• Press the round button twice. The current date appears on the display.
• Now press the minus button and the date of conception appears (window 9).
• Then press the plus button twice and the estimated date of birth appears in window 10.

Attention: before ovulation, the displays and symbols flash. After ovulation they are constantly illuminated. If no prediction is possible, the display.

30. Pregnancy confirmed

• If pregnancy is established, we recommend that you should continue taking temperature readings every morning during the first months.
• Baby-Comp keeps an eye on the development of the early pregnancy.
• In the event of a confirmed pregnancy the conception date and the date of birth remain constantly illuminated.
• Now is the time to make an appointment with your gynaecologist.

31. Back in operation after pregnancy

• You are not fertile during the first six weeks after the birth.
• The risk of becoming pregnant during the first six months after giving birth is low (2%) provided that you are fully and frequently breastfeeding your baby.
• After this and in all other cases, we recommend you to recommence temperature readings 6 weeks after the birth or even earlier. At first Baby-Comp shows "yellow". Slight fluctuations in temperature indicate that the normal cycle is reestablishing itself. Baby-Comp begins to show the usual fertility display.

1. Fertility indicators (from left to right) red = fertile, yellow = learning area, monophases, no ovulation yet, green = infertile
2. Alarm indicator: lights up when the alarm is switched on.
3. Display for all information concerning time, dates and temperature readings, day of cycle and demo-run (see pictogram windows 1-7).
4. Thermometer symbol: lights up during temperature reading time limit and flashes after pressing button.
5. Menstruation indicator: flashes for input +yes/-no menstruation.

1. Fertility indicators (from left to right) so far red = fertile, yellow = learning area, monophases, no ovulation green = infertile
2. Alarm indicator: lights up when the alarm is switched on.
3. Display for all information concerning time, dates, temperature readings, day of cycle and demo-run (see pictogram windows 1-10).
4. Thermometer symbol: lights up during temperature reading time limit and flashes after a button has been pressed.
5. Menstruation indicator: flashes for input +yes/-no menstruation.
6. Birth indicator: date flashes showing the possible date of birth, remains constantly illuminated for confirmed pregnancy.
7. Conception indicator: flashes on best days for conception and remains constantly illuminated for confirmed pregnancy.
8. Sex prognosis indicator: lights up if there is more likelihood of your conceiving a girl.
9. Sl data: flashes for input about sexual intercourse.
10. Sex prognosis indicator: lights up if there is more likelihood of your conceiving a boy.